T-shaped connector to join 3 pieces of LeakyPipe, in effect 'branching'. A simple push-fit barbed fitting without the need for additional clips.  Once connected, the pipe can be rotated on the fitting without breaking the seal.

This T-shape Connector is available in 3 sizes: the '12' size here fits LeakyPipe®.

T-Connectors for 16mm and 20mm supply pipe can be found here

SOLD IN PACKS OF 5 CONNECTORS 

20mm black polytube, available in 50m or 100m rolls

Non-porous 20mm pipe to deliver water from its source to the areas you want to water.

50m or 100m roll of a larger diameter black, non-porous, semi rigid plastic pipe, suitable as a permanent feeder pipe for your irrigation system. This pipe is easily cut with a sharp pair of cutters and is compatible with our range of '20' barbed fittings.  The fittings can be gently wiggled into the polytube and will grip on the internal surface without the need for additional clips.  In very cold weather, if it is difficult to insert fittings, try dipping the end into a thermos flask of hot water for about 10 seconds and this will soften the pipe slightly. As the pipe cools, it will shrink onto the barbed fittings.  Fittings can be rotated in the polytube without breaking the seal.

This LDPE (Low Density PolyEthylene) pipe is 20mm external diameter.

Push-fit, elbow-shaped connectors for LeakyPipe.

A plastic elbow suitable for making tight corners with LeakyPipe. The LeakyPipe itself is quite flexible and will easily curve around a 6" diameter, so the elbows are only really needed for the tightest corners. Simple push-fit, no additional clips are needed.

Available in 3 sizes: the 12mm size sold here fits LeakyPipe®

If you want to 'elbow' hosepipe or 16mm or 20mm polytube supply pipe, look under 'elbows'

SOLD IN PACKS OF 5 CONNECTORS!

20mm Compression Fitting with connections for LeakyPipe LP12 range.

(One or Two output options available for attaching one or two LeakyPipes)

Connect 20mm blue 'mains' MDPE pipe, to One output to LeakyPipe.   Also works with 20mm LDPE Black polytube instead of Blue MDPE tube.

Use these compression fittings where the water is supplied to the garden in 20mm blue MDPE 'mains' pipe. The output end is a barbed fitting which simply pushes onto the LeakyPipe.

Available for one or two LeakyPipe outputs - select from the "Outputs" option box above.

Sold as a single unit, pre-assembled with PTFE tape. The fitting can be rotated once assembled without breaking the seal.  High Quality Unidelta brand

Larger outputs are also available.
16 - fits 16mm polytube as single or double output.  CLICK HERE
20 - fits 20mm polytube as single or double output.  CLICK HERE

Pro-quality, 16mm compression to 3/4" female threaded adaptor.

There is no more secure way of quickly attaching 16mm supply pipe to a male thread (like the one you'll find on the output of a watering timer), than with this fitting.  16mm compressions will also make a tight fit onto most Garden Hosepipes too.

No fancy tools needed to fit this adaptor!  Just a sharp cutter.    

The fitting comprises three main parts.  

A black "body”, housing an internal, rubber "O” ring  
A blue threaded collar and a White plastic, toothed split ring.  

To make "compression” connection to a pipe, firstly feed the blue collar onto the pipe.  Then push the white split collar onto the pipe, just enough for the pipe to project about 25mm from the white collar.  Now offer the end of the pipe to the fitting body.  Push the pipe into the body and you’ll feel it stop against the internal "O” ring.  With a little more push & a wiggle, the pipe will slip passed the "O” ring for a further 25mm.  This will leave the white collar, settled very close to the black body.  

All you need to do after this is simply do-up the blue collar to hold the four things together!  It doesn’t need to be tight and the brilliant thing is, you can disassemble it very easily too.  They won’t blow apart and the seal is successful by way of the "O” ring sealing on the outside of the pipe wall.  Clever, isn’t it?

Just wrap PTFE "White" tape clockwise around the Male "Mating" thread, then wind the male and female threads together, to make that connection.  Sometimes you can achieve a compression seal between these two by inserting one or two rubber, flat washers into the female part, before doing-up the Male part.

Connect LeakyPipe to non-porous supply pipe & hosepipes.

These will connect LeakyPipe to your supply pipe.  Simply push together to connect the 2 pipes.  

Available sizes include:

• 16-12 - connect 1/2" hosepipe or 16mm supply polytube to LeakyPipe
• 20-12 - connect 20mm black supply polytube to LeakyPipe 

SOLD IN PACKS OF 5 CONNECTORS 

Tap for LeakyPipe® (12mm size)

A simple tap which allows isolation of areas from your irrigation system. Sold as a single unit.

These taps allow areas of your watering system to be switched on or off as required. 12mm size allows a section of LeakyPipe to be turned off e.g. a row on a vegetable patch 16mm or 20mm allow a whole section or your irrigation system to be shut down e.g. a particular border awaiting planting.

They have a barbed push-fit connection and clips are not needed.

Available in 3 sizes as shown:

• 12mm - fits LeakyPipe®
• 16mm - fits 16mm polytube or garden hosepipe
• 20mm - fits 20mm polytube

Please note these are NOT designed to hold back full (static) mains pressure.

Easy to use Battery-powered Watering Timer for Garden Taps.

Single output. Now, we do have stock of this timer.

Automatically water your garden while you are on holiday with a simple, reliable tap timer.

Surely the Easiest Tap Timer to Use

Similar to the great-value "Buddy” range, but with a heavier-duty brass input connection and better flow characteristics.  With a big dial to program your watering times, this is just about the simplest timer available at a very cheap price. Two good quality alkaline AA batteries will keep this unit running unattended all summer. 

Features:

• Simple connection to your tap.
• 3/4" thread output (suitable for hose snap or compression fittings).
• Programmable by watering duration, time of day and day of week (eg twice per week)
• Manual bypass for easy tap use.
• Rain delay for water conservation.
• 170mm High by 130mm wide by 60mm deep

Please bring this unit inside over winter to protect from frost damage. 

Proven to last and relieve you from the work of watering your plant collections, everywhere. A kit of 100m of LeakyPipe with a selection of 27 connectors including HoseSnap fittings for Planters, Beds and Borders.

Try the original 100m roll of LeakyPipe® Hose Pipe Kit

✔ Designed to water newly planted and established herbaceous borders.

This watering kit includes a superb porous hose which weeps water along its length.

This is a cost-effective leaky pipe irrigation system to water your garden borders. Includes 100m roll of LeakyPipe® with push-fit barbed connectors. Cut the LeakyPipe® LP12H into lengths as you lay it out and connect together to your hosepipe or 16mm black, Supply Pipe.    You can work the whole 100metres at one time, evenly.

A typical household tap pressure can water up to 300m LeakyPipe at one time. So you won't need the tap on much for all  100metres to work! This high quality rubber hose pipe will not perish or be affected by frost.

✔ It is reasonably flexible so you can snake it back and forth to water your borders, beds and shrubs.
✔ Specifically designed to easily water newly planted and established herbaceous borders, trees and hedgelines shorter than 100m.
✔ Includes connectors. Always in stock!
✔ It has proven to last in excess of ten years.

Buy a reliable hose pipe kit & Save time to water your plants. Arrange as rings or spiral around newly planted trees to aid their establishment. It works most efficiently when covered by a mulch or soil as evaporation is reduced. Overall you use less water with LeakyPipe than watering by hand and it will work out-of-sight whilst you enjoy your garden.

This hose pipe kit uses LP12H LeakyPipe

The LP12H is designed to be ideal for general purpose watering. This garden hose pipe is specifically manufactured by us to work on top of the ground, if you wish, as well as sub-mulch, working up to 50metres from the barbed connections. See video information here.

Buy this great quality hose pipe kit, which includes:

- 100 metres of LeakyPipe LP12H Porous Rubber Hose. This LeakyPipe® is not designed to used from a water butt, without pumping.
- 5  of 16-12 Reducer Connectors (Supply to LeakyPipe®).
- 5 of 16-12-16 Reducer Tees (Supply-Leaky®-Supply).
- 1  of 16-16-16 Tees (Supply-Supply-Supply).
- 2  of 12-12-12 Tees (To "Branch" LeakyPipe® to itself). 
- 10 of 12 plugs (A tidy way to plug LeakyPipe® ends).
- 2 of 16 plugs (A tidy way of sealing 16 supply pipe).
- 2 of 12-12 connectors (To connect Leaky-Leaky).
- 1 of Hosesnap-12 connector (Hose to Leaky®)
- 1 of Hosesnap-12tee connector (Hose to two Leakies)

N.B. 16 will fit both Supply piping and 1/2" garden hose, (even though the latter is a tight fit).  Also available in 50m, 100m, 250m, 400m rolls, with and without connections.

See this narrated video on system concepts and design.

Or the silent Video about LeakyPipe layout in Gardens on the next tab 

Tap for 16mm supply pipe or garden hosepipe.

A simple tap which allows isolation of areas from your irrigation system. Sold as single unit.

Available in 3 sizes as shown:

• 12mm - fits LeakyPipe®
• 16mm - fits 16mm polytube or 1/2" garden hosepipe
• 20mm - fits 20mm polytube

These taps allow areas of your watering system to be switched on or off as required. 12mm size allows a section of LeakyPipe to be turned off e.g. a row on a vegetable patch. 16mm or 20mm allow a whole section or your irrigation system to be shut down e.g. a particular border awaiting planting. They have a barbed push-fit connection and clips are not needed. 

Please note these are NOT designed to hold back full (static) mains pressure.

3/4" Male BSP threaded adaptor with barbed end to fit LeakyPipe® LP12 Porous Hose or garden hose or 16mm or 20mm polytube supply pipe.

A plastic adaptor with a 3/4" male thread converting to a barbed end of various sizes. Select the size you want above.

12mm - fits LeakyPipe® LP12 Porous Hose
16mm - fits garden hosepipe or 16mm supply polypipe
20mm - fits 20mm supply polypipe

SOLD IN PACKS OF 5 CONNECTORS

Small selection pack of 12 connectors.
Connects LeakyPipe to 16mm or 20mm supply pipe or garden hose.

A selection pack of 12 barbed fittings which will enable a range of designs to be made up using LeakyPipe and 1/2" garden hose, 16mm or 20mm polytube supply pipe. This pack is suggested to be used with a 50m roll of LeakyPipe in terms of providing a good range and number of fittings that you may want for setting up an irrigation system.  If you have 100m roll of LeakyPipe, consider a large selection pack.

The small 12mm ends will fit LeakyPipe. The larger ends can either be size 16 (fits 1/2" garden hosepipe or 16mm supply pipe) OR size 20 (fits 20mm supply pipe). Make your selection above.

This Pack of Barbed Fittings Contains:

• Two  - large equal tee, (allows branching of supply pipe in T shape).
• Two  - large size to LeakyPipe reducing tee, (Leaky 'tee's' out of the side of supply pipe)
• Two - reducing straight connector, (supply pipe to Leaky)
• Two - 12-12-12 tee, (allows branching of LeakyPipe in T shape)
• Two - 12-12 straight connectors, (Leaky to Leaky repair connectors).
• Two - 12mm end plugs for sealing the LP ends.
  

A Bargain, Discounted 100m Kit of The Original Leaky Pipe Porous Rubber Soaker Hose and Connectors.    It’s slow porosity is designed for sub-surface use. So after you’ve seen it working, cover it with soil, mulch or well-rotted manure.  You can "plant" it at the same time as you plant your Hedge plants.   It actually works better that way!

Protect your investment in hedge plants with LeakyPipe® sub-surface watering hose. Recommended by Professional Landscape Contractors.

Get the Perfect Hedging with our Hedge Watering Kit

Specifically designed and made by us for assured watering, this 100m hedge watering kit includes the original LeakyPipe® LP12L porous rubber soaker hose and connectors. It carries water further and consistently applies it over 100m length, slowly. It enables you to efficiently water new and established hedging. This kit includes all the fittings for a quick hook-up to your garden hose.    Of course, you can also plumb this into many different supply pipes, as you want.  Just select the appropriate fittings from our "Connections" pages.

The many Advantage of LeakyPipe 100m Watering Kit 

- Ideal for watering in new hedging
- Fast establishment and growing-on
- Waters up to 100m length
- Simple push-fit plugs and fittings included
- Adaptable to your hedge layout - cut LeakyPipe with sharp scissors and use 'tee' fittings.
- Hosesnap connectors for easy connection to your garden hose.
- Made in the UK
- Lasts for many years

Put LeakyPipe on the soil near the stems of the hedge plants, plug the LeakyPipe ends, connect to your garden hose, see it work, then cover with mulch or hoe into the topsoil for best efficiency of watering.

Connectors include in this Hedge Watering Kit: 

- 1 of HoseSnap to straight connector. (For one LeakyPipe length).
- 1 of HoseSnap to tee connector. (For two lengths of LeakyPipe).
- 5 of 12mm end plugs.
- 5 of 12-12-12mm tees to be able to branch LeakyPipe.

This is a great deal for 50metres of LeakyPipe, Connections and SupplyPipe.

Ideal for raised garden beds, raised borders, raised troughs or planters.

A comprehensive Kit to discreetly water up to 25m2 of raised beds or planters. Customise your kit by selecting sufficient connectors for 2-6 raised beds and choose between several options for supply pipe.

This kit includes lots of push-fit 'elbow' connectors to help fit an irrigation system to existing raised beds, borders, planters and troughs. You will need non-leaking supply pipe to carry the water up and over the wall of your bed. You can choose supply pipe to be included in your kit, or use small amounts of 1/2" garden hosepipe, which will also work with the connectors. Once at soil level, the pipe size 'reduces' down to that of LeakyPipe.  The LeakyPipe can be laid on the surface or covered in mulch which helps water wicking away from the LeakyPipe. Arrange the LeakyPipe around your plants. Moisture spreads outwards for about 12 inches / 30cm either side. If you need to branch the LeakyPipe within the bed, 'tee' connectors are included, as are 'plugs' for the ends of LeakyPipe.

A nail-in pipe clip keeps the pipe neatly in place on top of the wall of your raised bed / border. Lastly, a quick-connect hose-snap connector will allow connection to your garden hose.  

This Kit includes 50m roll of LP12H LeakyPipe, which is designed to be ideal for general purpose watering, working up to 50metres from the barbed connections.  It has proven to last in excess of ten years.

How to customise your kit 

1. Select the number of raised beds you have
2. Select if you would like any supply pipe (size and length). The fittings will be adjusted to ensure they are compatible with your selection.
3. Double check the total area of your beds do not exceed 25m2 - this will ensure that 50m of LeakyPipe at 50cm spacing is sufficient for your beds.

Items included:

• 50m roll of LeakyPipe LP12H Porous Rubber Hose
• 1 of 16-16-16 Tee.  (Allows branching of your supply network)
• 2 of 16 plugs.   (A tidy way of sealing supply pipe or garden hose)
• 2 of 12-12 connectors.  (To connect Leaky-Leaky, a useful repairer)
• 1 of HoseSnap to 16mm single straight connector (quick snap-on connection to regular garden hose)
• 1 of 16mm tee adaptor  (to allow quick snap-on connection to 2 lengths of supply pipe)

Each bed will get an additional set of: 

• 1 of 16-16-16 tee. (To branch supply pipe up behind your bed)
• 3 of 16 elbows (To bring supply pipe neatly over the wall of the raised bed)
• 1 of 16-12 reducer (To reduce pipe size to that of LeakyPipe)
• 1 of 12-12-12 tee (To branch LeakyPipe within the bed) 2 of 12 plugs (to seal the end of LeakyPipes)
• 1 of nail-in pipe clip (To keep supply pipe neatly in place on top of the retaining wall)

Imagine this.   Firstly, find a way of running the Supply tubing onto all the places you wish to water.  Use the Tee connection fittings and a pair of cutters, to tailor the tubing to give you a "Distribution Network" to carry the water to where you will be connecting the Leaky Pipe with the reducing connections.  Run the LeakyPipe near to the plants, - (within 30-50cm as the water will spread laterally) and plug the ends. (See this Video about fittings).

A high-quality, strong, durable and reliable connector for the end of your hosepipe. This fitting works really well when connecting to male hosesnap fittings, such as those on taps and other brass versions.

Pictures show both ends of the connector. Sold singly, (individually).

20mm Compression to 3/4" female Threaded Adaptor.
Sold Individually

Try our Reliable 3/4 Female AdaptorThere is no more secure way of quickly attaching 20mm supply pipe to a male thread (like the one you'll find on the output of a watering timer or tap) than with this fitting. 

No fancy tools needed to fit this adaptor! SOLD INDIVIDUALLY

400m Roll of Leaky Pipe Porous Rubber Soaker Hose (LP12H)

High quality 400m long porous hose pipe available in the UK. 

We manufacture LeakyPipe to ensure high standards.

LP12H General Purpose LeakyPipe is a porous garden hose which weeps water along its length. It will irrigate 50m lengths of pipe, although several lengths can be watered at once. A standard household tap pressure can water up to 300m LeakyPipe at once. It will not perish or be affected by frost. It is reasonably flexible so you can snake it back and forth to water your borders, beds and shrubs. Arrange as rings or spiral around newly planted trees to aid their establishment. It works most efficiently when covered by a mulch or soil as evaporation is reduced. Overall you use less water with LeakyPipe than watering by hand and it will work out-of-sight whilst you enjoy your garden.

The Original 400m porous hose pipe by Leaky Pipe

Soaker hose also available in 50m, 100m, 250m, 400m rolls.

25mm Compression to LeakyPipe connector
(One or Two output options)

Connect 25mm blue 'mains' pipe to 1 or 2 lengths of LeakyPipe.

Use these fittings where the water is supplied to the garden in 25mm blue MDPE 'mains' pipe. The output end is a barbed fitting which simply pushes onto the LeakyPipe. 

The following outputs are available.

12 - fits LeakyPipe as single or double output
16 - fits 16mm polytube as single or double output
20 - fits 20mm polytube as single or double output

Sold as a single unit, pre-assembled with PTFE tape. The fitting can be rotated once assembled without breaking the seal

Tap for 20mm supply pipe

A simple tap which allows isolation of areas from your irrigation system. Sold as single unit.

Available in 3 sizes as shown:

• 12mm - fits LeakyPipe®
• 16mm - fits 16mm polytube or garden hosepipe
• 20mm - fits 20mm polytube

These taps allow areas of your watering system to be switched on or off as required. 12mm size allows a section of LeakyPipe to be turned off e.g. a row on a vegetable patch. 16mm or 20mm allow a whole section or your irrigation system to be shut down e.g. a particular border awaiting planting. They have a barbed push-fit connection and clips are not needed. 

Please note these are NOT designed to hold back full (static) mains pressure

20mm Compression Elbow Fitting

20mm compression elbow for permanent, secure, leak-free 90 degree bends in 20mm black LDPE supply polypipe or 20mm blue MDPE pipe.

Secure connection, seals on the external surface of pipe.